How to Tile Over Vinyl Flooring

Laying a tile floor.

Can I lay ceramic tile over vinyl tile in my kitchen? I really don’t want to pull up the vinyl. -Linda

Hi Linda,

We receive more questions about tiling over an existing floor than any other. It seems like everyone wants to know what to do when they replace the floor in their kitchen or bath.

If the existing vinyl floor was installed over concrete and is glued down firmly, you should be able to tile right over it without any problem. Scrub the floor first to remove any dirt and grease then apply a bed of thin-set mortar and tile.

If the vinyl was applied over a wood subfloor, you should install 1/2” thick cement backer board on top of it first, using corrosion resistant screws driven into the floor joists. Another option to backer board on wood floors is one of the new polyethylene membranes such as Schluter®-DITRA. At only 1/8” thick, it can shave 3/8” off the finished thickness of your floor if height is a problem.

You can also tile directly over an existing tile floor as long as it is sound. As with vinyl, clean it first so the mortar will adhere well to the old tile.

For more information on tiling, check out our articles Tiling a Floor and Installing Tile Over a Wood Subfloor.

Danny

140 COMMENTS

  1. Hi Traci,
    You should be able to install a laminate floor over linoleum or vinyl as long as the old flooring is attached firmly and in good condition. Check to installation instructions that come with the laminate flooring for specific recommendations.

  2. Carol,
    Definitely take your toilet up and tile under it. If your toilet ever needs replacing, you might not be able to find one with a base that precisely matches the opening in the tile floor from where the old toilet is removed.
    Removing a toilet and re-installing it is a lot easier than having to re-tile your floor in case of toilet replacement.

  3. Danny. Is it difficult or even possible to remove ceramic tile that is installed over a vinyl floor? From what i have read, i don’ think i want to remove the vinyl floor from the concrete. Thanks

  4. I plan to tile my bathroom floor. It is a new house with linoleum currently laid down, so there likely is just particle board underneath. I plan to put down 1/2″ cement backing and then using 12×12 tiles. I will remove the toilet and tile under it, but do I have to remove the cabinets as well? Also, should the linoleum be pulled up or just lay the cement board on top of the linoleum. Thanks in advance.

  5. Can I put 12″x12″ self-adhesive tiles,over other self-adhesive tiles of the same size? Do you have to tile under the vanity, or can you cut the tiles to go around the vanity? Thanks

  6. Danny,

    I have a garage that was made into a room with the small, I think, asbestos tiles, from the 50s. I want to tile over this and was told I couldn’t do this. I don’t want to have to pay to have the asbestos tiles removed, if they really are. Can I put tile over these old tiles?

  7. Ihave stripped my kitchen down to the concrete sub floor but my dining area has a very secure vinyl 12 x 12 floring that I cannot pull up even with a heat gun. the two areas connect and I want to lay ceramic tile in both areas for continuity. There is a about a 1/4″ height difference between the kitchen and dining room floor. What can I do to even the areas out so I can lay the tile? Should I put backer board in the kitchen to be even with the dining area? I am stuck. Please help

    • Hi Carolyn,
      Yes, you can tile over existing vinyl flooring that was laid on concrete as long as it is firmly attached to the subfloor.

  8. Can I apply Ditra membrane directly to Formica countertop? Will thin set adhesive adhere to the Formica or do I need to do something to the surface first to make it adhere?

  9. I wish to lay ceramic tile in my kitchen. The floor is concrete with two layers of vinyl. I see that you have advised it was OK to put tile over a layer of vinyl if the vinyl is firmly glued to the concrete. In this case a second layer of vinyl has been placed over the first. Would you advise removing both layers of vinyl?

  10. What if I have a subfloor with vinyl then laminate, should I pull of the laminate and put down a backerboard or can I just clean the laminate and lay down the mortar then tiles?

    • Hi Beth,
      If you are refering to a floating laminate floor that resembles wood, you should take it up before applying tile. If it’s a glued down laminate, you might be able to apply the tile on top of it, but it wouldn’t be a bad idea to take it up first.

  11. I want to install hardwood flooring in my entire house. The problem is my home was built in the 60’s and has abestos tile covering the sub-floor and the floor is very uneven through out the house. I was told that I could lay the hardwood (or pergo) flooring over top of the tile and not to remove the tile for safety reason. How can I install the flooring and make the floor level at the same time?

    • Hi Bernadean,
      That is correct that you can leave the asbestos tile in place and cover over them without posing a major health hazard which would occur if you tried to remove them. Sounds like you need to use floor patch to level out the low spots in the old floor before installing the new one. Watch our video on How to Level a Subfloor to find out how.

  12. I have removed the vinyl flooring but there is paper from the back of the vinyl left behind. If I am tiling over this, do I need to completely remove what is left behind?

  13. what material should you place in between the plywood and the cement floor if the cement is the ground level (same level as outside ground) before nailing real hardwood floor to the plywood to block the moisture? Will felt paper be sufficient enough or do you recommend other material? thanks.

  14. Can you install ceramic tile over linoleum the might have mold under it? The linoleum has purple stains around the toilet and is glued down to a concrete slab.

  15. I have a similar question to Bernadeen. We have the vinyl tiles that probably contain asbestos. We want to lay engineered floor that isn’t floating down on this. Can we glue to the vinyl or do we need to lay something else down first? And is this safe to do over the vinyl tiles?

  16. I plan on renovating my bathroom and I wanted to lay ceramic tile. I have vinyl floors now…I wanted to lay the tiles on top of the vinyl but im not sure whats underneath…The vinyl is pretty sturdy and secure. Does it matter what material is underneath?

    • Hi Chris,
      If the vinyl is securely glued to the subfoor and the floor feels firm with no flex in to it, it should be okay to tile over it.

  17. I am installing sheet vinyl in a 3’x6′ power room which has an existing vinyl floor. The floor sits on truss joist and t&g plywood and I believe 1/4″ luan. I was planning to add an other layer of 1/4″ luan and nail as recommended. I am worried about the nail heads telegraphing through the new vinyl. Do you have any suggestions about altering my installation?
    Thanks for you help, Steve

    • Hi Steve,
      You might want to consider screwing the luan down then applying a filler to the screw heads to make them flush.

  18. Hi, I am putting ceramic tile in my kitchen and I pulled up hardwood flooring, which was over linoleum, which was then followed by vinyl floor tiles. . ., which left a black adhesive material. Can I apply the thinset mortar over the black adhesive or will this cause problems?

  19. Hi Phil…

    I’ve run into that situation many times. The main thing with that old black mastic was to knock down the ridges, high points, etc. It takes a little extra effort, but I could always accomplish it with just a long-handled scraper. Sweep the excess, then vacuum the whole area. At that point, you should be able to lay your tile. I also like to use the fortified thinset. It costs about $20-$25 a bag, but it goes a long way and holds better in my opinion.

  20. If i put laminate or tile over my vinyl in the kithchen what happens when I get a new dishwasher…how does the old one come out and the new one go in with different levels

    • Hi Donna,
      You are wise to think ahead concerning the height difference in your floor and the dishwasher before installing the tile. Depending on how high the adjustable feet on the dishwasher are now, you may be able to slide the dishwasher out, lower the dishwasher feet, tile the dishwasher space, and slide it back it. That way it will be easier to get it out in the future. If you tile up to the dishwasher, not only will there be a hump to go over when when you need to replace it, but you may have to remove the countertop to get the dishwasher out. Good luck with your project!

  21. I have white ceramic floor in my bathroom. (the tiles are sound)I want to lay vinyl tiles over the ceramic, can I do that and will it last.

  22. The upstairs bath (75 sf) in my 1950 house has two layers of sheet vinyl flooring over a solid subfloor. The plan is to install 12×12 ceramic tile. I’ve been told to: 1) remove both layers of vinyl before tile install; 2) install and nail backerboard over the vinyl then install tile; 3) spread a thin layer of concrete over the vinyl and install tile. Further comments received are that the floor is currently not level – well, it’s a 1950 house 🙂 – and that the concrete will make it earier to level the tile. Can you guide me in the right direction? Thanks.

  23. Can I put a layer of electric warming wires set in a mat on top of an existing vinyl floor, then under a layer of Ditra Mat and then set my ceramic tiles on top? The vinyl is glued to a wood subfloor in a master bath and it is very difficult to get it off.

  24. Hello,

    I have a basement room that takes on a little water from time to time and want to install tile. I removed one layer of laminate tile only to find another layer that I cannot remove. The floor is cement otherwise. Please tell me, how can I lay ceramic tile on this floor?

    • Hi Cheri,
      If the old vinyl is in good shape and glued down firmly with no seams popping up or holes, then you can put a new layer of vinyl flooring over a current layer.

    • Hi Halina,
      If the vinyl tile are well attached to the subfloor and not peeling up around the edges, you should be able to tile over it. Good luck with your project!

  25. Thank you for a your quick answer (kitchen tiles)
    I have one more question, thou.
    In a bathroom I do have a linoleum over subfloor. Can I lay ceramic tiles or let say marble tiles over it.
    That will be probably my first project (before kitchen)
    Thank you
    Halina

    • Hi Halina,
      As with laying tile over vinyl, as long as the subfloor and joists provide a firm foundation, the linoleum is well glued down, in good shape, and clean; you should be able to lay tile (or marble) over the linoleum. Of course, a layer of cement backer board is always a good idea to provide a more stable surface and aid in adhesion, if it doesn’t make your finished floor too high. Good luck with your project!

  26. Hi Danny. Sorry if this has already been addressed. I plan to tile my bathroom floor. I understand I have to remove the toilet but, do I have to remove the cabinets as well? And what about the tub that buts up to the tile?

    • Hi Sam,
      You can tile around the tub and cabinets when retiling your bathroom, just be sure to caulk the seam at the tub good with silicone caulk. Good luck with your project!

  27. Hi Danny – We are thinking of putting 12×12 tiles down in our kitchen, over an old vinyl floor. There is some flex in the floor, so we were planning to lay cement backer board over the vinyl – do we need to put thinset between the vinyl and the backerboard, or can we just screw the backerboard down?
    Thanks

    • Hi Trish,
      I’ve seen cement backer board installed both with and without thinset between the subfloor and backer board. Unless your building codes call for it, it’s up to you. The added thinset doesn’t hurt, though it will be harder to remove it if you ever need to. Keep in mind that the purpose of cement backer board is to provide a stable surface for the tile, not to provide added strength. Your floor joists and subfloor should be strong enough to prevent flexing on their own. Good luck with your project!

  28. Hi,
    This is probably a stupid question but how do I find the floor joists without taking up the subfloor? I want to retile a bathroom with ceramic or porcelain tile and the house was built in the 60’s and I am sure that the vinyl that was originally put in contains asbestos. The second layer of tile was a quickie job by the previous homeowner before selling us the house last year and is coming up all over the place, so i was going to remove it and put thinset and cement backerboard over the asbestos tile to be able to retile that floor without removing the asbestos layer. But I’m not sure how to find floor joists through the original tile to screw the backerboard into.

    • Hi Jaimie,
      While it’s a good idea to attach cement backerboard to the floor joists and align the joints in the backerboard so they meet on the floor joists, if you have a good firm plywood subfloor and screw (rather than nail) the backerboard down, you don’t have to hit the joists with the screws. However, if you want to find the floor joists, you can probably locate them by listening to the difference in sound when tapping the floor with a hammer, or use a stud finder that senses the hollow space between studs. If all else fails, use trial and error by hammering a small nail in where you think one of the joists is located until you hit it. Since the joists should be on 16″ centers, once you find one, you should be able to find them all by measuring. Then mark the ends of each one on the wall (or write down the measurements), so you can find them again once the backerboard has been laid down. Pop chalk lines on the backerboard and screw it down. Good luck with your project!

  29. I have vinyl floor glued down on a cement slab in the kitchen. I understand that I can lay tile over this. My question – the edges of the vinyl are raised just a little. Can I somehow just cut off these edges and find a way to level it out and lay the tile down. Except for the edges the rest of the floor is really glued tightly and I hate to try to remove the whole thing. Any suggestions?

  30. I have removed three layers of linoleum out of my kitchen to lay ceramic tiles. The last layer of linoleum had a paper backing and didn’t come up in a large area. I spent most of the afternoon scraping but I am wondering if I need to get it all up. I am planning to lay mortar/fiberock/mortar/tiles. Will the first layer of mortar even things out?

    • Hi Marti,
      If your tile floor is level and even, you should be able to install laminate flooring over it. Check out our article on Laying Wood Flooring Over Tile to find out more. Of course with laminate, you won’t glue the flooring down, like you would with wood or engineered wood flooring. Good luck with your project!

  31. i just bought a modular home and the whole floor is plywood then a layer of partical board… If i use thin set to lay the hardibacker then ceramic tile will this be enought?

    • Hi Dave,
      It’s not recommended to use standard particle board under ceramic tile, since moisture can cause it to fall apart, so I would remove the particle board and add another layer of plywood (if you need the extra height or the floor is not firm enough with one layer). Good luck with your project!

  32. Hi. I have a home built in approximately 1977 in Missouri. I want to place ceramic tile in my laundry room which currently has a vinyl flooring. I was told due to the age, the vinyl flooring may contain asbestos. I attempted to pull up the vinyl flooring, but it is well adhered all over and all I accomplished was tearing up pieces of the vinyl. I cut out some of the vinyl and sub-flooring and replaced some rotted flooring below with treated plywood and then another layer of treated plywood for the sub-floor. I still have the majority of the vinyl flooring left. I now wish to lay concrete board over the entile floor and then tile over the concrete board. My concern is that since I have disturbed the vinyl flooring, have I caused a health hazard? Is it safe to leave the current vinyl flooring and just concrete board and tile over it, or should I attempt to remove all of the vinyl, which would be a tremendous task for me? I don’t want to break any laws or have any liability issues should I ever wish to sell the home? Thank you for any advice you may provide.

  33. Hi Michael…

    Great question! I’m glad you’re responsible enough to look into this, too. Here are my suggestions.

    Since you have disturbed the vinyl, it would be to your advantage to purchase an inexpensive asbestos test kit and make certain whether or not asbestos is present. If it is, you may still be in good shape. While those tiny fibers can definitely be a health hazard, you may have only disturbed a minute fraction. I would use one of the popular type of floor cleaning systems (the ones that use the micro fiber disposable clothes), mist the area of floor with water, then mop it clean. Place the disposable pad in a sealed baggie and check your local yellow pages for proper disposal. Then, whatever you do….DON’T TEAR ANY MORE VINYL! 🙂

    The good news is that as long as it remains undisturbed, the EPA is fine with you covering it. I think you’ll be able to safely tile over the vinyl and encapsulate any remaining fears.

    Of course, if your testing finds an over-abundance of asbestos present, you’ll have to open up the wallet and turn to the professionals for removal.

  34. Hello,

    I know you had mentioned that when tiling you need to remove the toilet. But Do we need to remove toilet if we are putting down sticky 12×12 laminate tiles over sticky 12×12 laminate tiles? Or can we work around the toilet and put caulk like the bathtub?

  35. When removing ceramic tile in our home, we have discovered vinyl tile underneath which we believe to be original to the home (40 years old) and therefore likely to have asbestos. The ceramic tile is laid over plywood, which was over the original tile. Any tips on removing the ceramic and plywood layers with the least amount of disruption to the asbestos layer? We plan to recover with new ceramic tile.

  36. We just purchased an 1870 sq ft home built in 1951. It has original lino tile throughout adhered to a concrete slab. We will be floating a laminate wood floor in some areas, carpet in the bedrooms and Living area…we are up in the air regarding the wet areas…the tile in the kitchen and bathroom is coved up the wall about 3 inches with a metal trim band. Whether we choose to float a vinyl floor or tile, we need to remove that coving…any suggestions? We know the steps to keep the asbestos fibers contained…what is the best way to remove the coving? Thank you.

  37. Want to put ceramic tile in the kitchen, laundry room and bathroom. Subfloor is 2 layers of 3/4″ exterior plywood covered with sheet vinyl that is approx 20 yrs old. I have hydronic baseboard heat and the tile under the baseboard heaters is curling up…so is it best to pull up the old vinyl and then put down the ceramic? My fear is that not all of the adhesive will come up and I cannot have the height of cement backer board and tile, as the transition to the other rooms would be too much. I looked at Ditra but at $7 a linear foot it is just too expensive to use.

    • Hi John,
      While a subfloor of two layers of 3/4″ plywood is great, it’s overkill if your joists are on 16″ centers and the height of the floor is a problem.
      I would be to take up the vinyl and one layer of plywood, then put down 1/2″ cement backer board and tile on top of the 3/4″ plywood subfloor. Good luck with your project!

    • Hi Margaret,
      Depending on the specific type of flooring, you may be able to lay a laminate floor directly over vinyl flooring. If the vinyl is on a concrete slab, and there is moisture under the floor, you should put down a layer of 6 mil plastic first. See the installation instructions that came with your flooring to find out more.
      Good luck with your project!

  38. I am putting in 6″x 24″ ceramic tiles (approx) in the kitchen. I have pulled up some sheet vinyl and luan. Under that I found some green 12″ (vinyl?) squares, good condition, which appear to have been stapled directly on the plywood subfloor of at least 1 1/8″. Darn near impossible to get up. I plan to put down interior plywood stapled over the “vinyl” and then thinset, Hardibacker, thinset and ceramic tiles.

    Is that interior plywood layer actually required?

    If so, how thick should it be?

    Is the 1/4″ Hardibacker sufficient? I’d rather not go to the 1/2″ (nominal) unless this is strongly advisable. As is, it looks like the new floor may be roughly an inch higher than the old, requiring quite a transition to the hardwood floor dining room (& cutting a door shorter).

    • Hi Louis,
      If your subfloor is as thick as you say it is and doesn’t have any bounce, you can skip the plywood and go with just the cement backer board. 1/4″ backer board would be okay, as long as it’s attached well so there’s no movement in it. I have also heard of those who tiled directly over vinyl on a plywood subfloor with good results, if the vinyl is in good shape, and the floor is firm. Good luck with your project!

  39. CHANGE OF PLANS:

    I now think I’ll put 1/4″ HardieBacker directly on the hard green tiles, using thinset (probably modified). The remaining question is, should I run 60 sandpaper over the tiles first? I’m reading different opinions on this.

  40. I have just pulled the self adhesive tile up to find whole vinyl tile underneath that reeks of urine and shows water damage..so I pulled that up to find that half of it came up the other half only the top came off and paper and glue is stuck to yet another layer which is crumbling behind the toilet. Beneath that is wooden sub floor..can i scrape up what i can..spray with mildew and mold killer..patch with putty in lower areas and put cement board over the top? Or do i need to get it all up..

  41. What I actually did:

    It took us two days, but we pulled up the squares and got down to the subfloor. Turned out, some tiles were loose after all.

    BTW my ref to “interior” plywood should have been “exterior.”

  42. I am preparing to tile my kitchen and I have 3/4″ plywood as a subfloor and 1X4 wood planks under that. I cannot add any height to existing floor. Can I rip up the plywood subfloor and simply attach the cement board to these wood planks that sit directly on floor joists? The wood planks run on a 45 degree angle to floor joists.

  43. What is the size and spacing of the joists?

    BTW, direct attachment to planks is discouraged. Really need plywood or maybe even OSB.

  44. I plan to lay vinyl tiles over old linoleum floor in a bathroom. Most of the floor is fine, but there is one section that is peeled away. How do I level/ prep that section for installation?

  45. I am looking to replace a laminate floor with a ceramic tile floor. Original laminate. I was told i would have to lift all the cabinetry in the kitchen to do so. Is it possible to replace the floor with out removing the cabinetry?

    I understand i would have to remove the dihwasher etc.

  46. The problem with NOT removing, and flooring under everything, is you may end up with the dishwasher boxed in. You may then need to lift the countertop if you one day replace the dishwasher. If you are very careful, and somehow make it so you can install AND REMOVE the dishwasher without lifting everything up, have at it. And good luck. I don’t think it can be done. Thinset, CBU, thinset, and ceramic tile. That’s a LARGE increase in height.

    For just this reason, I decided to put my ceramic tile wall to wall in the kitchen. But then, I am replacing all my cabinets at the same time.

    Remove all the laminate, and any possible luan, down to the subfloor.

  47. Pam. To do it right, and have the job last, you need to remove the old flooring. After that, if need be, you can use leveling compound.

  48. Hey Louis :

    I believe I mentioned that i would have to remove the dishwasher and refrigerator from the kitchen. The oven is built into the wall. I would like to redo the whole kitchen with the cabinetry, but it isn’t an option at this time. What would be your suggestion. ??

    Mark

  49. I believe the problem would be getting the dishwasher back in. I’m assuming that it is a built in, under-counter dishwasher. You will raise the floor maybe as much as an inch. You’ll have to calculate it. Let’s assume 1/8″ laminate floor and 1/4″ luan under it. Remove those, and the floor is 3/8″ lower than it was. Then figure 1/8″ to 1/4″ thinset, then 1/4″ CBU, then 1/4″ thinset, then 1/4″ ceramic tiles. So your new floor will be roughly 1/2″ to 3/4″ higher than it was, possibly more. The dishwashers I have dealt with will not have that much play in their height adjustments. You simply won’t be able to fit it back in without raising, and thereby probably destroying, the countertop.

    Do you plan to reinstall the dishwasher after the floor job?

    You could remove the baseboards, including any quarter round, and tile up to the cabinet kickplates and walls. Leave a 1/8″ to 1/4″ gap that you later fill with caulk (not grout or thinset). Then, in some future year, you could replace the cabinets. But they would have to have an almost identical layout to the current ones. You then put in plywood to raise the level of the cabinets to the tile level, and reinstall the dishwasher. Or if you want a different cabinet layout, you could fill in with tiles. But the grout will give you away, as it will never match.

  50. I have the same problem as Carla, but her question remains unanswered. I have stripped my dining room down to the concrete sub floor but my kitchen has a very secure vinyl floring that has no issues. The two areas connect and I want to lay ceramic tile in both areas for continuity. There is a 1/8″ to 1/4″ height difference between the kitchen and dining room floor. What can I do to even the areas out so I can lay the tile? Is there something I can lay down in the dining room to make it even with the kitchen, or should I just make the thinset thicker in that area? I am stuck, too. Please help!

  51. If I tile over the existing vinyl. My tile will be higher than my carpet. Do they make a ceramic trasition strip that will match the tile?

  52. HELP… I am wanting to put cermic tile around my bathtub and have been told it will be hard to get this done with out leaking down the road! How and what can I do to make sure this dosen’t happen.

  53. I am planning on replacing kitchen and bathroom floors with ceramic tiles. I need to clarify the article above. The way I’m reading this is that if I use the Schluter-Ditra membrane I do not need the cement backer board. Am I reading this correct.

    I have a subfloor, underlayment (1/4 inch) and a single layer of securely glued vinyl flooring that I am hoping to leave in place.

  54. I have a half inch plywood subfloor and three quarter inch particle board on top of that-there are two layers of vinyl flooring attached to the particle board-can i put three eights plywood over the vinyl and screw down to first layer of plywood -this will be for a kitchen floor that is very well braced to concrete crawl space. I intend to do floor with slate

  55. About 5 years ago, we had a “contractor” come and install a new subfloor to our 50 year old home in the bathroom. In doing so, he told us that we DID NOT need to use backer board. Never having a ceramic floor before, we went along with it. As you may guess the tiles cracked, came loose etc…We would like to put down new tile. Can we put backer board on the existing tile or will we have to destroy the tile and then add the backer board?

  56. The tile in our shower floor is constantly building up with mildew. We have regrouted, resealed, scrubbed and cleaned and keeps coming back. We spray with clorox and nothing seems to work. Our plan is to redo the existing tile floor without removing the existing tile. I am wanting to know if you can lay new ceramic tile over existing tile in a shower floor? What are the best and least expensive options?

  57. i am tiling my kitchen. can i tile up to the cabinets. I dont want to take them up. i have a dishwashwr but it has adjustible wheels

  58. I have been using Bono laminate floor cleaner on my laminet floors but the last time I bought it I accidentally picked up Bono hardwood cleaner. My question is can I use the Bono hardwood cleaner on my laminate floors without hurting them?

  59. We just purchased our first home and started fixing it up. In the kitchen we layed pergo over laminate flooring with a layer of thin foam between them. Now, only 4 weeks later, the pieces are rising and water/goo is coming out of all the cracks. There are areas that are completely bowed already. We don’t know what to do and we already poured so much money into it. Is there anything we can do to fix this?

  60. I am renovating a former rental townhouse built in 1980. I am planning to use a laminate through the townhouse with ceramic tile in the bathroooms. They are relatively small bathrooms and currently have what I believe is linoleum (or it could be vinyl, I’m not sure I know the difference.)

    The floors creak a little when they’re walked on, so I’m guessing the subfloor needs some type of repair. The floors leading up to the bathrooms are carpeted. The carpet is being removed and the laminate is going down.

    I have never tiled before, but would like to do this myself to save money. I’m concerned that the floors in the bathroom and bedroom/hallway will not be level with each other when all is said and done.

    How do I ensure that when the subfloor is properly repaired, tile is laid in the bathrooms, and laminate is installed in the bedroom/hallway everything will be seemlessly level?

    Also, I’m replacing the vanity cabinets in the 2 bathrooms. Should I replace them before or after tiling? The design of the cabinets has an opening on the bottom. I’m thinking that I should tile under them because there would be no way to seal.

    Thanks for the assistance!!

  61. Im in west Memphis AR! I’m about to try this method over vinyl flooring with concrete floor underneath. Wish me well I will keep you posted and thanks!

  62. I want to lay a stone type tile flooring in my kitchen. The problem is I have laminate flooring laid over old asbestos tile. My dishwasher has leaked and swollen some of the laminate. The floor is on top of fir strip flooring. Can I screw the laminate down and lay the tile over top if I use lots of screws and make the fllor really secure ? I don’t want to take up the asbestos tile or laminate as my cabinets are installed on top and if I lay another layer of subfloor the floor will be too high for my doors to swing meaning I will have to cut them down.

  63. I plan to lay Vinyl tiles over Linoleum Floor in my bathroom. Do I need to remove the toliet or can i cut the tile to fit around the toliet?

  64. Question:
    I want to lay tile over an existing vinyl floor. The existing vinyl is layed on a wood subfloor. Because thinkness is an issue, can I use a polyethylene membrane over the vinyl or do I need to use the cement substrate?

  65. We have a 1960s house, with small squares of ceramic flooring–black and white. A few pieces are missing at the closet door, and at the bathroom door. It’s a small house and I don’t want to, nor can I afford, a whole renovation. I just want it to look better. Can we use linoleum over the ceramic tiling?

  66. I have vinyl tiles on the floor.The edges on these tiles have risen but the raise is extremely minute. Can I put new tiles over these tiles or can I glue felt paper on the existing tiles and then put the new tiles on top of the felt paper. The new tiles are peel and stick.

  67. I am getting ready to put 12 x 12 linoluem squares over an existing linoluem floor. Can I just stick them directly on the old floor?

  68. Query:
    ~ Is it possible to directly install Daltile floating porcelain tiles over a vinyl covered bathroom floor?
    ~ What would be the appropriate prep procedure?
    ~~ ” Gracias.” ~~

  69. On one floor of house I’m building– I Have two layers of 5/8 inch osb as subfloor and it is spongy in some spots between the engineered 24 inch on center floor trusses-other floor is 2 layers of 5/8 inch plywood and not spongy. I want to polyurethene the spongy osb subfloor which will harden the sub floor-it’s not damaged- and then put down vct tile on polyurethened wood osb sub floor,– can I do this? and if so will a urethene adhesive hold down the vct tile on a polyurethened wood osb sub floor.

  70. I am trying to remove the linoleum in my kitchen and carpet in the dining area and tile both. (dining area is high traffic) BUT, the kitchen has plywood under the linoleum making it higher than the dining area. Can I use the plywood as a substitute for backerboard in the kitchen and add the backerboard in the dining area only … then the height would be right for a continuous floor.

  71. I would like to lay cermic tile in my Utility Room that currently has lenoleum. It is seal great except for the small stip that was layed in the back about four inch wide which is turning up. Is there something I can do to make those edges lay down and be able to put the cermic tile on top of them without removing the lenoleum in total. The cermic tile has its own sticky back and we intend to use grout inbetween them. If I do have to remove it first – it would be the sub-flooring I would be laying the cermic tile on….does this need to have further prep before proceeding with the tiling.

  72. Excellent,excellent page good answers,and good information,love read it alot. I have a question about Shulter-Ditra.Maybe I missed it before,but can you put that on gluedown tile 12×12 and then install ceramic tile

  73. Hi i want to lay ceramic tiles in my kitchen the existing lino tiles are pulling up really easily and there is a very thin very hard black layer left on the concrete which i assume is the old adhesive but like i say its very thin , flat and hard , does it all have to come up before i lay the ceramic tiles ? Thanks

  74. I got this site from my pal who shared with me about this web site and now this time I am visiting this web page and reading very informative posts at this place.

  75. Hi I want to lay ceramic tiles in basement.i recently pulled up carpet in basment do to flooding and revealed 9×9 old tiles that im sure contain asbestos that have carpet adhesive on top of tiles.my question is can I use cement leveler on parts that tiles are missing so I can lay backer board down and do I need to lay a thinset down before I putbacker board down so to make sure I have a nice secure even floor for tiles to be set.the floor is cement with old asbestos tiles with carpet glue please if you have any thoughts or suggestions I would appreciate it very much thank you.

  76. Hello, we live on a concrete slab and currently have those self adhesive 12 x 12 tiles on the floor, which were installed over existing (I am sure asbestos)commercial type tiles. We want to install sanded plywood flooring on top of this. What would be the best way to do so…glue down, nail down using concrete nail gun or both? Thanks for any input!

  77. Hi. My question is similar to one above regarding a manufactured home. Our home has OSB board with vinyl overlay. Can I tile on top of all of that or do I still need to remove the OSB? I do not know if there is plywood under the OSB. Thanks!

  78. Thanks for the great post, I have a tricky question from Sweden. In our apartment (from 70s) uses an interesting combination of Round Gravel layer on top of Concrete Floor. Then on top of round gravel, there are plywood boards, and finally Vinyl flooring on top of that. Now I want to lay ceramic tiles on top of that in our kitchen area, the floor is pretty firm and does not bend or squeak with normal load.

    My Question is, can I lay Ceramic tiles on top of existing Vinyl Floor just by simply using ceramic tile adhesive/glue? or do i need a Polythylene sheet also?
    Thanks in advance

  79. Thanks. I think 1/2″ backer board is for walls and 1/4″ for floors on thin set. Yes i can see the need for 1/2″ if your floor is weak. But great article.

  80. While hoping to just put down tile over old bathroom vinyl floor, we decided to pull up flooring about 4in from the walls only to find moisture on concrete subfloor. We continued to remove all vinyl and found moisture in some areas, now we are not sure how to continue??? We have purchased “mapelalstic aqua defense” for another tile project, wondering if that would work? The house was build in early 70’s, near the coastline!!! What should we do to continue our project?

  81. Installing PVC plank tiles with tongue and groove over vinyl self-adhesive tiles. Do I need to use a glue or an underlayer?

  82. Hi,
    Is it okay to lay a levelling substrate directly over lino tiles? And if so, what properties does the substrate need? I want to lay ceramic tiles over a concrete floor covered in lino but this needs levelling first.
    Many thanks.

  83. Hi,
    I have a large room which has vinyl tile. I want to place ceramic tile over this and was told by a local store that I have to remove the existing vinyl before I can place ceramic tile as the vinyl is not porous and the ceramic tile will not adhere to the vinyl floor. Can you give me a suggestion as to what I can place over this vinyl?
    Thanks,
    Dottie peterson

  84. I had a professional floor company install procelon tiles in my kitchen and requested removal of two sheets of old vinyl and possibility of new subfloor due to the height the finished floor would be above my hardwood dining room floor. I was ignored and the floor was put over the existing two vinyl and subfloor and is now one inch higher than hardwood floor. The company suggests a reducer to transition. You comments as to my recourse is greatly appreciated. I had no problem with cost of work with removing vinyl and subfloor and expressed this to the salesperson.

  85. I am concerned about the health risks posed by the PVC in the old vinyl tiles in my kitchen. I have recently read that PVC can pose a health threat. Is it sufficient to cover over them or do I need to remove them before installing Marmoleum click-it tiles? Is it safe to have the old PVC tiles underneath the tiles? These tiles have a cork backing and click together. I was told I did not need to remove the old flooring for installation purposes but my concern is more about the PVC remaining under the surface. Can you address this? Thank you.

  86. Hello,

    I am laying tile in the entrance of a manufactured home that is on a permanent concrete foundation. I’m reviewing options for the tile base layer and would like to minimize (or eliminate) any height increase for the new tile portion. The subfloor is particle board that currently has vinyl floor on it.

    Thanks for any and all advice!

    Felix

  87. Can I put thinset and wonder board on top of existing vinyl tile to create to foundation and will regular thinset adhere to the existing vinyl tile?

  88. Hello. I have three floors that I want to install ceramic tile. One has vinyl tiles that came with the adhesive already on it. The second room is ceramic tile. The third room is ceramic tile with a sealant on the entire floor. Can I put ceramic tile on all these floors without removing the current flooring? The sub floor is concrete. Do I need to scuff or sand the top layer?

  89. i installed a bench section on the back of my shower in tile i did not use it so i removed the bench and now i have to lay ceramic tile and need to lay it in an angle for drain please send information.

  90. I am laying a laminate flooring and half the room was carpet which has been removed the other is linoleum. Do I have to remove it or can I lay over it. thank you floyd

  91. I am removing carpet off a bedroom floor and installing a floating laminate floor. I have a couple squeaks that I know I can remove by screwing down through the joist. However, I have a concern in that the original flooring is still in tact and consist of vinyl asbestos tiles. I realise that the carpet underlay and carpet served as encapsulating the vinyl asbestos and understand that likewise , the new foam underlay and laminate will also serve to encapsulate it. Would it be wise/safe to screw through these tiles to fix the squeaks before installing the new flooring?

    Thanking you in advance,

    Merv

  92. My Rhino flooring is coming unglued from my concrete floor. Can I just install tile over that flooring or do I have to remove it? They glued my Rhino floor to the concrete but it is lifting in some areas and would prefer to just put tile over it.

  93. Dilemma: Home is on a concrete slab foundation. I need to install a waterline to Fridge which is located on opposite side (across) the kitchen sink area where the water pipes are located. Rather than running a water line from under the kitchen sink through and behind drywall up through the ceiling into the attic then across and down in between the adjacent drywall and out the wall to the fridge’s water and ice dispenser, how about running a 1/4″ PEX (Plastic) waterline tubing within a carefully cut 1/4″deep trench-like groove in the 1/2″ thick cement backer board flooring then applying the mortar before laying down the new kitchen tiles over the backer-board with the inlayed plastic waterline tubing? Would this work? Remember, the fridge is about 6 to 8 feet on the other side of the sink were the water pipe?

  94. As a long time follower of allowing older Americans to live comfortably in their home,
    I appreciate your post. Regrettably, lots of people today would
    prefer to take the easy way out and recommend a assisted living facility for their aging loved ones.
    I have actually tweeted a link to your blog and bookmarked
    the site.

    Thanks once again for your quality post.

LEAVE A REPLY